• ucl_drone

ROS 2 Documentation

The ROS Wiki is for ROS 1. Are you using ROS 2 (Humble, Iron, or Rolling)?
Check out the ROS 2 Project Documentation
Package specific documentation can be found on index.ros.org

Overview

This package contains the implementation corresponding to the following master theses:

• Towards 3D Visual SLAM for an Autonomous Quadcopter Running on ROS. (A. Leclère, A. Jacques)
• Suivi d'une cible mobile par des drones autonomes. (J. Gérardy, F. Schiltz)

Abstract 1 — In a context where multi-copters gain in attractiveness each day to solve novel challenges or replace older technologies, the need for autonomous behaviour is being pointed out as a key feature for unlocking lots of applications. This master thesis is conducted at UCL for trying to understand the current challenges to unlock multi-copter autonomy. We point out that the lack of robustness of all current state-of-the-art implementations which are based only upon on-board sensors, leads, as a common flaw, to a lack of accuracy of the pose estimation. Indeed, for GPS-denied environments such as indoors, there exist poor absolute references to build an accurate and robust belief of the position and orientation of the drone. Unfortunately, indoor situations need precisely the best pose estimation since they are confined places not allowing too large errors while executing movement. We propose an implementation of the direct keyframe-based visual SLAM approach based on features detected in the images of the video-stream of an embedded camera. We show that the results obtained on a real low cost quadcopter, the AR.Drone 2.0, improve substantially the pose estimation, notably by canceling the drift on sensor readings. However, this technique presents strong limitations when confronted to untextured environments, due to the lack of reference keypoints detected in the images. To palliate this, we explore the state of the literature to propose some promising advances to replace or enhance this approach, such as replacing conventional cameras by RGB-D (Red Green Blue - Depth) cameras or DVS (Dynamic Vision Sensors), or replacing computationally costly software parts by a hardware implementation, or better fusing the available sensors informations.

This is a video of an AR.Drone 2.0 executing a demonstration, using this package:

Abstract 2 — In this thesis, we describe a system that enables a low-cost quadcopter coupled with a ground-based laptop and a router navigate autonomously in previously unknown and GPS- denied environments. The first drone searches for a moving target in a 3 by 3 meters room. when it finds it, it starts following it. When its battery level becomes critical, it calls an other drone to replace him and it goes back to its starting position.

This is a video of two AR.Drone 2.0 executing the mission, using this package:

Quickstart

Installation

It is advised to use "indigo" version of ROS.

1. Install the ardrone_autonomy package. To do this, follow intructions at http://ardrone-autonomy.readthedocs.io/en/latest/installation.html

OpenCV 2.4.x and PCL (Point Cloud Library) are also needed. To install them, follow the procedures on their respective official websites.

Install ucl_drone package:

# cd into ros root dir
roscd

# clone repository
git clone git:https://github.com/Felicien93/ucl_drone.git

# compile in the root of ucl_drone package
catkin_make

Set up the router

As several drones communicate during this mission, it is mandatory to use a router and make the drones act as clients instead of hosts. The model we used was the "TPlink « TL-WR841N »" but any model should do.

The first step is to collect the MAC addresses of the drone you will use.

#Connect your computer to the drone's network

#Use telnet to access the drone network informations
telnet 192.168.1.1

#Display relevant informations
ifconfig ath0

#Note the drone's MAC address. You will need it later. It is written in the "HWaddr" field. MAC address example: 90:03:B7:2A:DF:11

#Set up your network card
sudo ifconfig eth0 192.168.1.253

#Type the IP address of your router in your internet navigator
192.168.1.254

#Connect on the page using the password and ID of the router

#Go in Network>Interfaces>Edit>LAN and define 192.168.1.254 in the ipv4address field.

#Go in Network>wifi and click add. Use the controller with "BGN" in his description.

#In "general setup" configure the essid fiel on "drone" and hide essid.

#Go back in Network>wifi and click "enable" next to the "drone" network

#Click on "edit". Go in Mac filter, chose "allow listed only" and add the MAC addresses of the drones you connected.

#In your files (not in navigator) go in src>ucl_drone>drone_preparation>Appareillage and add one file per drone. The file name should be the drone's network name (example: ardrone2_00217) and it should contain the IP address you want it to have (example: 192.168.1.5)

Run

# Connect to the drones. Go in src>ucl_drone>drone_preparation>Appareillage
bash autoconfarparrot

# run the program
roslaunch ucl_drone two_simples_new.launch